Home | Industrial And Mechanical | Industrial Equipment


Composite Moulding

By: Richard Hayward



Composite Moulding is a process which enables the manufacture of a specifically designed product from a composite material, one such Composite material is Glass Reinforced Plastic, also known as Fibreglass; Composite moulded products can be manufactured for use in most industry sectors, such as,


  • Construction,
  • Leisure,
  • Marine,
  • Aerospace,
  • Automotive,
  • Defence,
  • And many more.


Composite moulded products can be manufactured to meet most requirements and specifications, further-more, these components can be produced to any size, shape or colour required, in some cases peripheral components can be incorporated into the moulding process, such as threaded inserts ect, these can be bonded into the product to provide a fixing solution, or metal work can be incorporated into the moulding to provide a mount for internal components such as electronics ect, During this innovative process, additional reinforcements can be incorporated into specific areas which will be under load or receive additional stresses; this is done during the laminating process, when additional layers of reinforcement can be applied into the required areas, or structural sub-mouldings can be bonded in, in short, composite moulded components can be tailored to meet any requirement, but lets talk about the process that makes it all possible, Composite Moulding.

Composite Moulding is a process that starts off with the manufacture of a pattern also known as a plug or buck, this is a model made from Polyurethane foam, or MDF (Medium Density Fibreboard) or another material, this model will replicate the required product exactly, with regards to the dimensions and surface finish, once the pattern has be manufactured and prepared with the relevant release agents the mould can be manufactured from it, the mould can be male or female depending upon the design of the product.
The manufacture of the mould requires a certain amount of skill and understanding, its this experience that will enable the correct tooling materials to be chosen and employed during the mould construction, the mould may need to be more than one piece depending upon the design of the product (flash lines, undercuts, intricacy, ect are things to give thought to) if the mould is to be more than one piece, then locators will be required on the flanges to ensure the mould section align.

Now the mould has been manufactured and allowed to cure, the pattern can be removed from the mould, the use of compressed air or wedges may be required to break the seal between these parts, once the pattern has been released, the mould can be prepared with several coats of mould release wax, remember before you run the mould a coat of PVA (Poly Vinyl Alcohol) release agent is also good practice and will help the first product to release from the mould with out the risk of sticking.

Now the mould is prepared and ready to go to work, its time to go Composite Moulding,

1. This starts with the mould being painted or sprayed with gel-coat of the desired colour; the polyester gel-coat is the coating that will provide the pre-coloured finish to the moulded component, the gel-coat is allowed to cure, but will remain tacky, this is good, the tacky finish will enable a good bond for the laminate,

2. Once the gel-coat has cured, a layer of glass fibre is then applied to the back of the gel-coat, the layer of glass-fibre is then saturated with resin, the saturated glass-fibre is then rolled with a special roller, this is to remove any trapped air, and to consolidate the glass-fibres, more layers of glass-fibre can be applied and consolidated until the required thickness is achieved, the laminate is then left to harden and cure.

3. Once the laminate has cured, the product can be released from the mould, the product is normally left in the mould for twenty four hours, this ensures that the product has no imperfections, like, print through from the glass-fibre, shrinkage in the gel-coat ect, but remember, if there are any defects like the one's just mentioned, these can all be rectified by a skilled operative.

Congratulations, you now have a small insight into Composite Moulding, a truly innovative process for manufacturing Composite components, and remember you probably see products every day made using this process, but you didn't realise it, that was until now!

Article Source: http://articlepowerplant.com

About Author:
Richard Hayward from Fibreglass UK writes about COMPOSITE MOULDING visit www.fibreglassuk.com for all your COMPOSITE MOULDING requirements. The COMPOSITE MOULDING is to be the same as the article title and click through to www.fibreglassuk.com




Please Rate this Article

 

Not yet Rated

Click the XML Icon Above to Receive Industrial Equipment Articles Via RSS!
Additional Articles From - Home | Industrial And Mechanical | Industrial Equipment
Sign Up for a free account
Article Directory Software
Click here to download the exact software that powers this directory for FREE. Start your own article directory today!
Submit Articles
Member Login
Top Authors
Submission Guidelines
Ezine Notifications
Article RSS Feeds
About Us
Link to Us
Contact Us
Privacy Policy
Terms of Service

Recommended Webmaster Resource: http://www.linkdirectory.com

Article Powerplant
6280 Matchette, Suite 301
  Windsor, ON, Canada

Site Concept And Images © 2007 - 2008 Article Powerplant
All Rights Reserved
Contact Us


Powered by Article Dashboard